秀山KVVRP4X1.5电缆现货春季
Ratedpower-fre/U:0.6/1kV.•电缆导体的最高允许长期工作温度（PVC/XLPE）:70℃/90℃.siblecontinuousoperatingtemperatureofconductor(PVC/XLPE):70℃/90℃•短路时（最长持续时间。
Precautions for installation of power cables: keep 2m distance when the cable is installed in parallel with the thermal pipe, and 0.5m should be maintained when crossing. The cable shall be installed at a distance of 0.5m in parallel or across other pipelines. When the cable is directly buried and installed, the buried depth of 1-35kv cable is not less than 0.7m. When 10KV and below cables are installed in parallel, the net distance between them shall not be less than 0.1m and 10-35kv shall not be less than 0.25m. The distance of cross installation is not less than 0.5m. Cable laying temperature is not lower than 0 ℃, bending radius: multi-core cable or 15 (D + D), a single cable 20 or more (D + D), (D for cable diameter, D) for the conductor diameter. 6 kv and above cable joint: (1) installing a cable terminal head, must be stripped semiconductor electric shielding layer, operation shall not damage the insulation, should avoid mark uneven situation, when necessary use sand paper to grind; The shield end should be flat and the graphite layer (carbon particles) should be cleaned. (2) plastic cable end copper tape screened and armor must be good grounding, the short circuit also follow this principle, avoid unbalanced three-phase run ShiGang armoured end produce inductive electromotive force, and even "lighter" and accidents such as burning sheath. It is required to use my tinplate to braid copper wire for grounding lead. When connecting with the cable copper belt, it should be welded with chromium-iron tin. The shield of three-phase copper tape should be connected with ground wire respectively. Note that the shielded ground wire and steel armor ground wire should be separately drawn out and insulated from each other. The position of the welded ground wire should be as low as possible. Basic re for cable terminals and intermediate joints: a. good conductor connection; B. The insulation is reliable, and it is recommended to use irradiated cross-linked heat-shrinkable silicone rubber insulation materials; C. good sealing; D. sufficient mechanical strength to meet various operating conditions. The end of the cable must be used to prevent erosion of water and other corrosive materials, so as to prevent breakdown due to the aging of the insulation layer caused by water trees. Crane or forklift should be used for the loading and unloading of cables. It is forbidden to run flat or lay flat. For installation of large cables, cable laying cart should be used to avoid external damage or abrasion caused by manual dragging. If the cable cannot be laid in time for some reason, it should be stored in a dry place to prevent sunlight from exploding and water entering the end of the cable. Note: the installation of wire and cable should be done by the installation personnel or full-time technical personnel familiar with the performance of wire and cable. If there are still unclear matters, please consult the relevant technical department or the technical department of our factory.
也可提供双层护套的通信电缆。展望未来，任重而道远。公司期待能与新老客户真诚合作不段把握时代脉搏，与时俱进，共创**。我厂生产煤矿用阻燃控制电缆,主要规格有MKVV,MKVV22,MKVV32等，各种产品均有《煤安标志》证书，规格齐全，产品广泛应用于各大煤矿系统和煤矿监控系统。
耐火电缆选用根据耐火电缆的具体特性，设计人员在设计选用时应注意以下几个问题：(1)当耐火电缆用于电缆密集的电缆隧道、电缆夹层中，或位于油管、油库附近等易燃场所时，应首先选用A类耐火电缆。除上述情况外且电缆配置数量少时，可采用B类耐火电缆。
20年后，电路设计一般是：进户线6—10mm2，照明2.5mm2，插座4mm2，空调6mm2专线。单芯电线1.5平方电线，用于灯具照明，单芯电线2.5平方电线，用于插座。单芯电线4平方电线用于3匹空调以上，单芯电线6平方电线用于总进线，双色线用于接地线。
三相380V电机应用非常广泛，在某些只有单相电源的情况下，也可以通过一些办法把三相电机改为两相电机的。但是也容易存在一些问题。比如：启动困难、输出功率不够，大约只有60%左右、转矩小没力、容易发热、长时间运行影响寿命等。改造前提首先必须要确定三相电机的三个绕组首尾端是否正确。三相电机首尾端如果错乱，改了以后会引起电机烧毁。如果三相电机接线端子没拆过，或者接入三相电能正常运行，说明端子是正确的。也可以直接看电机接线盒里的端子编号排布，正确排列如下（注意看线标）：接线三相改单相一共Y型和△型两种接法。
执行标准：JB8734.5-1998产品数量长期大量供应包装说明200米/卷；500米/卷线芯材质无氧铜芯数1～24芯护套材质PVC/PE电线最大外径26（mm）标称截面0.12～2.5（mm2）RVVP RVVP 屏蔽电缆缆芯：绝缘芯线绞合成缆，绕包聚酯薄膜带（PP带） RVVP 屏蔽电缆护套：黑。
Forlayingindoors、intunnelorcabletrench,unabletobearexternal-corecableinmagneticductisnotpermissibleNH-VYNH-VLY聚氯乙烯绝缘聚乙烯护套耐火电力电缆PVCinsulatedPEsheathp。
DJYPVPR 聚乙烯绝缘对绞铜线编织分屏蔽及总屏蔽聚氯乙烯护套软计算机电缆 敷设室内、电缆沟、管道等要求静电屏蔽场合。DJYP2VR 聚乙烯绝缘对绞铜带分屏蔽聚氯乙烯护套软计算机电缆 敷设室内、电缆沟、管道等要求静电屏蔽场合。
HPVV配线通信电缆。描述：电缆用全色谱的实心聚乙烯绝缘，经过绝缘的导线被扭绞成线对，由线对绞合成缆芯。电缆缆芯外加上适宜的缆芯包覆材料，聚氯乙烯护套。结构：导线无氧铜线，高密度聚乙烯绝缘，聚氯乙烯护套，并按照全色谱标明绝缘线的颜色。
该电缆主要用于交流或直流300V及以下的工作系统，在500V及以下时能正常工作。金属屏蔽电力电缆适用于额定电压0.6/1kv及以下的交直流电力系统中的输送电能用。产品具有较强的电磁干扰、抗雷击及均衡电位、改善供电品质的特性，特别适宜计算机中心、航空航天监控中心、智能大楼等精密电子装置的场所。
MHYBV(PUYBV)煤矿用聚乙烯绝缘镀锌钢丝编织铠装阻燃聚氯乙烯护套通信电缆5-501/0.8用于机械冲击较高的平巷、斜巷煤矿用阻燃通信电缆……mh聚乙烯绝缘……Y铜质线芯……省落铝-聚乙烯粘结护层……A聚乙烯内护层……省落铜丝编织铠装……B蓝阻燃聚氯乙烯护套……V钢丝铠装蓝阻燃聚氯乙烯护。
为了进一步理解电路工作原理，在看图分析时可以采用直流等效电路法、交流等效电路法，对电路进行静态、动态分析。直流等效电路法就是在输入信号为零时，各级放大电路在直流电源作用下的工作状态，实际上就是找出直流通路，确定各级电路在静态时的偏置电流和电压。交流等效电路法就是在输入信号不为零时，确定电路的交流信号通路及工作状态。应当注意的是，在采用等效电路法分析是，要根据元器件性质给予特别处理。如电路中含有电容、电感这两种元件时，电容具有“隔直通交”的作用，电感具有“隔交通直”的作用。
煤矿用聚氯乙稀绝缘和护套阻燃控制电缆天津市电缆厂MKVVMKVV22MKVV32MKVVRMKVVRPMKVV（2-61芯）MKVV芯） MKVVR （2-61芯）MKVV芯） MKVVP （2-61芯）煤矿用阻燃屏蔽通信电缆MHYVP一、产品用途及特点本产品适用于矿山、井下环境监控系统中传输通信。
七：基本电缆规格及结构参数线芯*标称截面(mm2)导体结构(根数*直径)(B/R)mm电缆最大外径(mm)参考重量(kg/km)YVFRYVFRPYVFRYVFRP0-72-95-。