YH电缆格YH灵宝格合理YH电缆格YH美丽
Precautions for installation of power cables: keep 2m distance when the cable is installed in parallel with the thermal pipe, and 0.5m should be maintained when crossing. The cable shall be installed at a distance of 0.5m in parallel or across other pipelines. When the cable is directly buried and installed, the buried depth of 1-35kv cable is not less than 0.7m. When 10KV and below cables are installed in parallel, the net distance between them shall not be less than 0.1m and 10-35kv shall not be less than 0.25m. The distance of cross installation is not less than 0.5m. Cable laying temperature is not lower than 0 ℃, bending radius: multi-core cable or 15 (D + D), a single cable 20 or more (D + D), (D for cable diameter, D) for the conductor diameter. 6 kv and above cable joint: (1) installing a cable terminal head, must be stripped semiconductor electric shielding layer, operation shall not damage the insulation, should avoid mark uneven situation, when necessary use sand paper to grind; The shield end should be flat and the graphite layer (carbon particles) should be cleaned. (2) plastic cable end copper tape screened and armor must be good grounding, the short circuit also follow this principle, avoid unbalanced three-phase run ShiGang armoured end produce inductive electromotive force, and even "lighter" and accidents such as burning sheath. It is required to use my tinplate to braid copper wire for grounding lead. When connecting with the cable copper belt, it should be welded with chromium-iron tin. The shield of three-phase copper tape should be connected with ground wire respectively. Note that the shielded ground wire and steel armor ground wire should be separately drawn out and insulated from each other. The position of the welded ground wire should be as low as possible. Basic re for cable terminals and intermediate joints: a. good conductor connection; B. The insulation is reliable, and it is recommended to use irradiated cross-linked heat-shrinkable silicone rubber insulation materials; C. good sealing; D. sufficient mechanical strength to meet various operating conditions. The end of the cable must be used to prevent erosion of water and other corrosive materials, so as to prevent breakdown due to the aging of the insulation layer caused by water trees. Crane or forklift should be used for the loading and unloading of cables. It is forbidden to run flat or lay flat. For installation of large cables, cable laying cart should be used to avoid external damage or abrasion caused by manual dragging. If the cable cannot be laid in time for some reason, it should be stored in a dry place to prevent sunlight from exploding and water entering the end of the cable. Note: the installation of wire and cable should be done by the installation personnel or full-time technical personnel familiar with the performance of wire and cable. If there are still unclear matters, please consult the relevant technical department or the technical department of our factory.
HYA通信电缆，HYA22HYA23铠装通信电缆HYAT600对400对200对通信电缆价格充油式通信电缆规格型号：ZRC-HYATZRC-HYAT23HYATHYAT23HYAT53 大对数电缆25对大对数电缆报价25对大对数电缆大对数电缆报价大对数电缆生产厂家 3类大对数电缆大对数电缆是HYA 。
If it is true that the products provided by our company are not in conformity with the re of the contract due to the problem of the products, we agree to the buyer to exchange or reject the products and return the goods.
国家煤安证查询安标国家矿用产品安全标志中心（矿用产品安全标志办公室）根据国家安全生产监督管理总局的授权，承担矿用产品安全标志管理工作，包括受理安全标志申请，组织实施技术审查、现场评审、产品抽样检验，核发安全标志和企业持证后的监督管理。
本厂生产的射频电缆的结构是多种多样的，可以根据不同的方式和型式来分类。射频电缆按结构分类（1）同轴射频电缆同轴射频电缆是最常用的结构型式。由于其内外导体处于同心位置，电磁能量局限在内外导体之间的介质内传播，因此具有衰减小，屏蔽性能高，使用频带宽及性能稳定等显著优点。
PLC系统中使用的模拟量有两种，一种是模拟电压，一种是模拟电流，模拟电压最常见，用的也最多。模拟电压一般是0~10V，并联相等，长距离传输时容易受干扰，一般用在OEM设备中。模拟电流一般是4~20mA，串联相等，抗干扰能力强，dcs系统中一般都使用模拟电流。首先，我们先要用传感器测量我们所需要的参数，通过变送器将此参数变换成0~10V或者4~20mA，现在很多传感器都是自带变送器的，直接就输出模拟量，建议大家在项目中选用此种类型的传感器图二某压力传感器手册如图二所示，是某压力开关的选型手册，红色圆圈部分是它的量程0~250公斤，再看黄色荧光笔部分，此型号的传感器是模拟电流输出，也就是此款传感器将0~250公斤的压力线性转换成了4~20mA的电流，当我们检测到12mA的电流时，就表示压力是125公斤，依此类推。
电缆阻燃性能试验符合GB/T18380的规定，如用户不要求按C类阻燃要求。电缆烟浓度应符合GB/T17651的规定，其最小透光率为60%。卤素含量测定应不大于100mg/g。其它性能要求同GB9330的规定。
注名：根据使用环境的需要还可生产此类电线电缆的阻燃类（ZR）、耐火类（NH）、交联类（YJ）产品产品介绍-矿用控制电缆:MKVV矿用控制电缆|MKVVR矿用控制软电缆|MKVVP矿用屏蔽控制电缆|MKVV32矿用铠装控制电缆|MKVVRP矿用屏蔽控制软电缆|MKVV22矿用铠装控制电缆|ZR-MKV。
二：产品执行标准Q/HHTZH007.1阻燃性能试验执行GB规定三：使用特性1．交流额定电压：U0/U0.6/1KV最高工作温度：105℃最低环境温度：固定敷设-40℃2．电缆安装敷设温度应不低于-25℃。
技术特点1.电缆额定工作电压1000v.；2.导体结构采用多层复绞形式，电缆弯曲性能高；3.绝缘护套材料经改性后，具有高阻燃性，氧指数超过32；4.电缆的长期工作温度可达105℃,从而可使电缆载流量比普通电缆提高1.3倍；5.电缆符合IEC332-3《电缆成束燃烧试验》标准规定的A级水平。
Suitable for railway automatic block, chain of axle, station properties rather than stuff coded, computer, microcomputer monitoring, scheduling, scheduling focused, high-power electric switch machine and related e and control devices between transmission control information and monitoring information and power.
具有良好的信号传输性能。带米标识，分100米、200米、500米、1000米木轮包装。 2、铝箔、裸金属丝编织双层屏蔽，PVC外护套，阻燃,外观紫色。 3、符合VDE 0472标准；B类试验（IEC332.1）。
以上各相的交链磁通用“式2”表示，电流i用“式3”表示：上式中，KK3为基波和三次谐波的系数。转子以同步速度转动，下式成立：θ=ωt-δ根据以上式子，各相转矩合成的三相电机转矩如下式所示：即三相电机的转矩K3项消去，不受磁通三次谐波的影响，不含成为一恒定转矩。另一方面，两相电机的情形也同样变成如下式所：根据上式，两相合成转矩的两相式细分驱动时的转矩T2变成下式：根据上式，第1项为一恒定转矩，第2相为含ω的振动转矩。
芯数从2芯到24芯之间按国标分色，两芯以上绞合成缆，外层绞合方向为右向，软圆无氧铜线或镀锡无氧铜线屏蔽，广泛应用于仪器、仪表、楼宇对讲、监视监控的控制安装。天津市电缆总厂第一分厂经营多种“RVVP屏蔽电缆”，竭诚为您提供的完善的售前、售中和售后服务，专业提供“RVVP屏蔽电缆”技术咨询等服务。
计算机电缆1、计算机电缆执行标准：参照采用英国BS5308、日本JCS189。2、计算机控制电缆用途：本产品适用于额定电压450/750V及以下或直1000V及以下的发电、冶金、石化等工矿企业集散系统、电子计算机系统、自动化系统的信号传输及检测仪器仪表等。
HYA553铜芯实心聚烯烃绝缘挡潮层聚乙烯护套单层纵包轧纹钢带铠装聚乙烯套市通信电缆HYAT553铜芯实心聚烯烃绝缘填充式挡潮层聚乙烯护套双层纵包轧纹钢带铠装聚乙烯套市内通信电缆ZRCHYA铜芯实心阻燃聚烯烃绝缘挡潮层聚乙烯护套单层纵包轧纹钢带铠装聚乙烯套市通信电缆传输音频、150。
4.成缆时把四根线芯排列为红，绿，蓝，白，排流线，排流线要和线芯一起绞合，千万不要纵放，成缆时不要加填充物，缆芯外用铝箔绕包，而后再绕包一层聚酯膜，在外有一层铜丝编织屏蔽（屏蔽铜丝不镀锡）。5.护套：护前直径是8.2毫米，护后直径12毫米（11.7--12毫米之间），护套为阻燃蓝色护套一、产品用途及特点：本产品适用于矿山、井下环境监控系统中传输通信信号。