一、316L高压卡套过滤器的简介：
316L高压卡套过滤器，顾明思义就是过滤的作用，其材质是不锈钢，中力阀门有限公司主要生产的不锈钢、碳钢等材质，也可根据客户要求定制。它是除去液体、气体中少量固体颗粒的小型设备，可保护设备的正常工作，当流体进入置有一定规格滤网的滤筒后，其杂质被阻挡，而清洁的滤液则由过滤器出口排出，当需要清洗时，只要将可拆卸的滤筒取出，处理后重新装入即可，因此，使用维护极为方便。
二、316L高压卡套过滤器的工作原理：
316L高压卡套过滤器是输送介质的管道系列不可缺少的一种装置，通常安装在减压阀、泄压阀、定水位阀或其它设备的进口端，用来消除介质中的杂质，以保护阀门及设备的正常使用。该法兰式Y型过滤器具有结构先进，阻力小，排污方便等特点。法兰式Y型过滤器适用介质可为水，油、气。可按用户要求制作滤网，其外型基本相同（Y型），内部件全部采用不锈钢，坚固耐用。当需要清洗时，只要将可拆卸的滤筒取出，去除滤出的杂质后，重新装入即可，使用维护方便。
过滤精度可由滤网的大小来控制，过滤面积可定做。Y型过滤器一般通水网为18-30目/cm2，通气网为40-100目/cm2,通油网为100-300目/cm2。过滤器会产生阻力损失，水用过滤器在一般计算额定流速下，压力损失为0.52～1.2kpa。
ST34T型过滤器是除去液体中少量固体颗粒的小型设备，可保护设备的正常工作，当流体进入置有一定规格滤网的滤筒后，其杂质被阻挡，而清洁的滤液则由过滤器出口排出，当需要清洗时，只要将可拆卸的滤筒取出，处理后重新装入即可。
三、316L高压卡套过滤器的特点：
1、进出口通径:原则上过滤器的进出口通径不应小于相配套的泵的进口通径，一般与进口管路口径一致。
2、公称压力:按照过滤管路可能出现的压力确定过滤器的压力等级。
3、孔目数的选择:主要考虑需拦截的杂质粒径，依据介质流程工艺要求而定。各种规格丝网可拦截的粒径尺寸查下表"滤网规格"。
4、过滤器阻力损失计算:水用过滤器，在一般计算额定流速下，压力损失为0.52~1.2kpa
四、316L高压卡套过滤器的性能：
1、适合物料;
a、化工、石油化工生产中的弱腐蚀性物料，如:水、氨、油品、烃类等;
b、 化工生产的腐蚀性物料，如烧碱、纯碱、浓稀硫酸、碳酸、醋酸、酯酸等;
c、制冷中的低温物料，如:液甲烷、液氨、液氧及各种制冷剂;
d、 轻工食品、制药生产中有卫生要求的物料，如:啤酒、饮料、乳制品、粮浆医药用品等
2、过滤精度:10-480目(一般通水网为18-30目/cm2，通气网为40-100目/cm2，通油网为100-480目/cm2。)
3、工作温度:≤90℃
4、公称通径:DN25-DN600mm
5、公称压力:PN≤1.6Mpa(其它工作压力可按用户要求设计)
6、法兰标准:GB81-59(也可按用户要求制造)
7、壳体材质:A3、304、304L、316、316L
8、密封材料:聚四氟乙烯、耐油石棉胶安装与使用
五、316L高压卡套过滤器的安装说明：
1、过滤器安装时介质的流向必须与阀体上箭头方向一致，垂直时要求水流方向是自上而下
2、应安装在距所保护阀门的距离是其通径的6-10倍处；
3、安装此阀门的管路必须设置旁路；
4、进出口压力差大于0.2MPa时应进行清理或清洗；
网上的图片仅供参考，有特殊要求的或介绍不明的，请致函来电，江苏中力阀门有限公司欢迎您！！！
First, the introduction of 316L high pressure card sleeve filter:
316L high-pressure card sleeve filter, Gu Mingsi is the role of filtration, the material is stainless steel, Zhongli Valve Co., Ltd. mainly produces stainless steel, carbon steel and other materials, can also be customized according to customer re It is a small device that removes a small amount of solid particles from liquids and gases. It protects the normal operation of the e When the fluid enters the filter cartridge with a certain size filter, its impurities are blocked, and the clean filtrate is discharged from the filter outlet. When cleaning is required, the detachable filter cartridge can be taken out and reloaded after processing, so that it is extremely convenient to use and maintain.
Second, the working principle of 316L high pressure card sleeve filter:
The 316L high pressure ferrule filter is an indispensable device for the series of pipes for conveying media. It is usually installed at the inlet end of pressure reducing valve, pressure relief valve, fixed water level valve or other e to eliminate impurities in the medium to protect it. Normal use of valves and e The flange type Y filter has the characteristics of advanced structure, small resistance and convenient sewage discharge. The flange type Y filter is suitable for water, oil and gas. The filter can be made according to the user's re Its outer shape is basically the same (Y type), and the inner parts are all made of stainless steel, which is sturdy and durable. When it is necessary to clean, remove the detachable filter cartridge, remove the filtered impurities, reload it, and use it for maintenance.
The filtering accuracy can be controlled by the size of the filter screen, and the filter area can be customized. The Y-type filter generally has a water-passing net of 18-30 mesh/cm2, a ventilation net of 40-100 mesh/cm2, and a through-oil net of 100-300 mesh/cm2. The filter will cause a loss of resistance. The water filter has a pressure loss of 0.52 to 1.2 kPa at a generally calculated nominal flow rate.
The ST34T filter is a small device that removes a small amount of solid particles from the liquid. It protects the normal operation of the device. When the fluid enters the filter cartridge with a certain size filter, its impurities are blocked, and the clean filtrate is filtered by the filter. Discharge, when cleaning is required, just remove the removable filter cartridge and reload it after handling.
Third, the characteristics of 316L high pressure card sleeve filter:
1. import and export diameter: In principle, the inlet and outlet diameter of the filter should not be less than the inlet diameter of the matched pump, which is generally consistent with the inlet pipe diameter.
2. Nominal pressure: Determine the pressure level of the filter according to the pressure that may occur in the filter line.
3, the choice of the number of holes: mainly consider the particle size of the impurities to be intercepted, according to the process re of the media process. The size of the screen can be intercepted by various specifications. Check the table below for "Filter Specifications".
4, filter resistance loss calculation: water filter, under the general calculation of the rated flow rate, the pressure loss is 0.52~1.2kpa
Fourth, the performance of 316L high pressure card sleeve filter:
1. Suitable for materials;
a. Weak corrosive materials in chemical and petrochemical production, such as: water, ammonia, oil, hydrocarbons, etc.;
b. Corrosive materials produced by chemical industry, such as caustic soda, soda ash, concentrated sulfuric acid, carbonic acid, acetic acid, ester acid, etc.;
c. Low temperature materials in refrigeration, such as liquid methane, liquid ammonia, liquid oxygen and various refrigerants;
d. Light-duty foods and pharmaceuticals that have hygienic re, such as: beer, beverages, dairy products, grain and medical supplies, etc.
2, filtration accuracy: 10-480 mesh (general water network is 18-30 mesh / cm2, ventilation network is 40-100 mesh / cm2, oil network is 100-480 mesh / cm2.)
3. Working temperature: ≤90°C
4. Nominal diameter: DN25-DN600mm
5, the nominal pressure: PN ≤ 1.6Mpa (other working pressure can be designed according to user re)
6, flange standard: GB81-59 (can also be manufactured according to user re)
7, shell material: A3, 304, 304L, 316, 316L
8. Sealing material: installation and use of PTFE and oil resistant asbestos rubber
5. Installation instructions for 316L high pressure ferrule filter:
1. When the filter is installed, the flow direction of the medium must be the same as the direction of the arrow on the valve body. When vertical, the flow direction is required from top to bottom.
2, should be installed in the distance from the protected valve is 6-10 times its diameter;
3. The pipeline for installing this valve must be bypassed;
4. When the pressure difference between the inlet and outlet is greater than 0.2MPa, it should be cleaned or cleaned;
The pictures on the Internet are for reference only. If there are special re or the description is unknown, please write to us. Jiangsu Zhongli Valve Co., Ltd. welcomes you! ! !