自承式电缆识别和长度标记：电缆外表面有**性识别标记，标记间隔不大于1m，标记内容有：导线直径，线对数量，电缆型号，制造厂厂名代号及制造年份，长度标记以间隔不大于1m标记在表面上综合纽绞铁路信号电缆执行标准GB/T。
二、产品执行标准：企业标准三、使用特性：1．额定电压：UO/U300/500V.2．导体线芯最高工作温度：聚氯乙烯及低卤低烟阻燃聚氯乙烯绝缘：70℃和105℃两种聚乙烯绝缘：70℃；交联聚乙烯绝缘：90℃无卤低烟阻燃聚烯烃：70℃无卤低烟阻燃交联聚烯烃90℃和125℃两种3．最低环境温度：固定敷设－。
3、绝缘电阻见下表：性能聚氯乙烯绝缘交联聚乙烯绝缘体积电阻率ρΩ.㎝20℃时电缆工作温度时-1012绝缘电阻常数KiMΩ.㎞20℃时电缆工作温度时36.70.03673.67■型号名称型号名称铜芯铝芯VV-PYJV-PVLV-PYJLV-P聚氯乙烯(交联聚乙烯)。
HBYV、HBV-J、HBZR、HBZR-J、HBYV-J、HBYY、HBVV、HBVV-J、HPV、HBV产品执行标准：参考邮电局YD/T630-93标准.型号：HBYV、HBV-J、HBZR、HBZR-J、HBYV-J、HBYY、HBVV、HBVV-J、HPV、HBV型式代号:HB-室内线代号V。
VVR32铜芯聚氯乙烯绝缘钢丝铠装聚氯乙烯护套软电力电缆。VLV32铝芯聚氯乙烯绝缘钢丝铠装聚氯乙烯护套电力电缆。KYJVZR-KYJV铜芯交联聚乙烯绝缘聚氯乙烯护套控制电力电缆敷设在室内、电缆沟、管道固定场合。
STEP7-Micro/Win在程序编辑器窗口里为每个POU提供一个独立的页。主程序总是第1页，后面是子程序或中断程序。因为各个程序在编辑器窗口里被分开，编译时在程序结束的地方自动加入无条件结束指令或无条件返回指令，用户程序只能使用条件结束和条件返回指令。通常将具有特定功能且多次使用的程序段作为子程序。子程序可以多次被调用，也可以嵌套（最多8层），还可以递归调用（自己调用自己）。子程序有子程序调用和子程序返回两大类指令，子程序返回又分条件返回和无条件返回。
五、代号名称和含义项目代号说明耐火特性NH耐火电缆A或B系列代号K控制电缆绝缘材料V聚氯乙烯、阻燃聚氯乙烯Y聚乙烯YD低烟无卤聚烯烃(YDJ低烟无卤交联聚烯烃)YJ交联聚乙烯F氟塑料分200℃和260℃护套材料V聚氯乙烯、阻燃聚氯乙烯F氟塑料分200℃和260。
适用于交流额定电压0.6/1KV及以下的行车、台车、传输机械等移动电器用动力传输线及控制、照明、通讯线路，本产品已广泛应用于冶金、电力、船舶、港口等行业。执行标准：GB。＊最小弯曲半径：无铠装电缆应不小于电缆外径6倍；有铠装电缆应不小于电缆外径12倍3、用途：＊适用于交流额定电压uo/u为450/750v及以下的控制，监控回路及保护线路。
Local cable USES manufacuring HYA, HYAT, HYAC, HYPAT, HYPA and HYA53 HYAT53, HYPA53 HYPAT53 type cable is designed for main telephone switching area, relay telephone cable, manufacuring HYA, HYAT, HYPA and HYPAT is mainly used for pipe laying, also can be used for overhead, but need to disconnect; HYAC only applies to overhead, no need for suspension lines or hooks; The HYA53, HYPA53, and HYPAT53 cables provide the mechanical strength and corrosion resistance of the cables. They can be laid in any way, which is more suitable for direct burial in rock areas. The operating temperature is -30 ~60 degrees.
WDZ-KYDYDRP铜芯无卤低烟阻燃聚烃绝缘聚氯乙烯护套铜线编织屏蔽控制软电缆。WDZ-KYDYDRP2铜芯无卤低烟阻燃聚烃绝缘聚氯乙烯护套铜带屏蔽控制软电缆。WDZ-KYDPYDP2铜芯无卤低烟阻燃聚烃绝缘聚氯乙烯护套铜带屏蔽控制电缆。
对称射频电缆主要用在低射频或对称馈电的情况中。（3）螺旋射频电缆同轴中的导体，有时可做成圈状，借以增大电缆的电感，从而增大了电缆的波阻抗及延迟电磁能的传输时间，前者称为高阻电缆，后者称为延迟电缆。如果螺旋线圈沿长度方向卷绕的密度不同，则可制成变阻电缆。
可传输电话、电报、数据和图像等。而且本电缆厂的通信电缆生产厂分布全国各地。中国除生产长途型通信电缆和市内话缆外，光纤电缆和聚烯烃绝缘综合护层全塑市内话缆也有了长足的发展，国内不少厂家和科研单位从国外引进技术和设备开始生产。
交流发电机的产品代号有JJFZ、JFJFW四种，分别表示交流发电机、整体式交流发电机、带泵交流发电机和无刷交流发电机。第2部分为电压等级代号。用1位阿拉伯数字表示，1-12V；2-24V；6-6V。第3部分为电流等级代号。用1位或2位阿拉伯数字表示，其含义见表1-3。表1-3电流等级代号电流等级代号123456789电流A～1920～2930～3940～4950～5960～6970～7980～89≥90第4部分为设计序号。
煤矿用控制电缆参数说明:::::参数说明煤矿用控制电缆 MKVVMKVV22MKVV32MKVVRMKVVRP MKVVP煤矿用控制电缆产品执行标准：MT煤矿用控制电缆用途：本产品适用于交流额定电压u0/u为450/750V及以下的控制监控回路及保护线路和配电装置中电器仪表的连接线。
Precautions for installation of power cables: keep 2m distance when the cable is installed in parallel with the thermal pipe, and 0.5m should be maintained when crossing. The cable shall be installed at a distance of 0.5m in parallel or across other pipelines. When the cable is directly buried and installed, the direct buried depth of 1-35kv cable is less than 0.7m. When 10KV and below cables are installed in parallel, the net distance between them shall not be less than 0.1m and 10-35kv shall not be less than 0.25m. The distance of cross installation is not less than 0.5m. Cable laying temperature lower than 0 ℃, bending radius: multi-core cable or 15 (D + D), a single cable 20 or more (D + D), (D for cable diameter, D) for the conductor diameter. ? 6KV and above cable connector:? When installing the terminal head of the cable, the semiconductor electrical shielding layer must be stripped off. During operation, the insulation shall not be damaged. The shield end should be flat and the graphite layer (carbon particles) should be clean. (2) plastic cable end copper tape screened and armor must be good grounding, the short circuit also follow this principle, avoid unbalanced three-phase run ShiGang armoured end produce inductive electromotive force, and even "lighter" and sheath and other accidents. It is required to use my tinplate to braid copper wire for grounding lead. When connecting with the cable copper belt, it should be welded with chromium-iron tin. ? The shield of three-phase copper tape should be connected with ground wire respectively. Note that the shielded ground wire and steel armor ground wire should be separately drawn out and insulated from each other. The position of the welded ground wire should be as low as possible. Basic requirements for cable terminals and intermediate joints: a. good conductor connection; B. The insulation is reliable, and it is recommended to use irradiated cross-linked heat-shrinkable silicone rubber insulation materials; C. good sealing; D. sufficient mechanical strength to meet various operating conditions. The end of the cable must be used to prevent water and other corrosive materials from corroding, in order to prevent the water tree caused by the aging of the insulation layer and breakdown. Crane or forklift should be used for the loading and unloading of cables. It is forbidden to run flat or lay flat. For installation of large cables, cable laying cart should be used to avoid external damage or abrasion caused by manual dragging. If the cable cannot be laid in time for some reason, it should be stored in a dry place to prevent sunlight from exploding and water entering the end of the cable. ? Note: the installation of wire and cable should be familiar with the performance of wire and cable installation personnel or full-time technical personnel, if there are still unclear matters, ball related technical department or technical department of our factory.