Eight core SYV - 75-5 coaxial cable of the radio frequency cable, home video line, etc., are SYV solid core polyethylene insulated PVC sheathed coaxial cable, 75 of which means the resistance of the conductor is 75 ohms, 5 large diameter refers to the insulation of the cable is 5 mm (4.8 + / - 0.2 mm), 5 instead of 7, 7 cannot replace with 5, because insulation in large and small, not big to small generation.
MVV电缆，MVV22电缆，MYJV电缆，MYJV22电缆，MYJV32矿用电力电缆产品适用于煤矿井下额定电压0.6／1KV及以下输配电线路。矿用电力电缆的功能是长期安全可靠地传输容量的电能。还有直流输电系统用的直流矿用电力电缆。
如数控机床、电子设备、五金冲压、木材石材机械、玻璃与门窗机械、注塑机、机械(人)手、建筑机械、重型机械厂、汽车制造、起重运输设备、自动化仓库、码头等室内外环境需要的场所。如数控机床、电子设备、五金冲压、木材石材机械、玻璃与门窗机械、注塑机、机械(人)手、建筑机械、重型机械厂、汽车制造、起重运输设备、自动化仓库、码头等室内外环境需要的场所。
(3)、敷设电缆时的环境温度不低于0℃，最低环境温度：固定敷设-40℃，非固定敷设-15℃。(4)、电缆最小弯曲半径：非铠装层或编织屏蔽的电缆，应不小于电缆外径的6倍，有铠装或铜带屏蔽结构的电缆，应不小于电缆外径的12倍。
计算机电缆技术参数：产品额定电压(U0/U):300/500V长期工作温度为70℃敷设时环境温度不低于:固定敷设-40℃,非固定敷设-15℃最小弯曲半径：无铠装层应小于电缆外径的6倍，带铠装层的电缆应不小于电缆外径的12倍在20℃时用直流500V电压试验稳定充电1min后绝缘电阻应不小于2500MΩ。
从的等效电路看到，这个振荡电路是一个桥形电路。R1CR2CRt和RE1分别是电桥的4个臂，放大器的输入和输出分别接在电桥的两个对角线上，所以被称为RC桥式振荡电路。RC桥式振荡电路的性能比RC相移振荡电路好。它的稳定性高、非线性失真小，频率调节方便。它的振荡频率是：当R1=R2=R、C1=C2=C时f0=12πRC。它的频率范围从1赫～1兆赫。调幅和检波电路广播和无线电通信是利用调制技术把低频声音信号加到高频信号上发射出去的。
EISC - SS fire-retardant explosion-proof intrinsically safe cable EISC - SS - R flame retardant. Explosion-proof intrinsically safe cable (wire) (business standard) the enterprise standard main technical indicators are reference articles IEC227 (1979) preparing publications and British BS5308Part1 standard materials. Purpose: this product is designed for laying sites with rated ac voltage of 450/750v or less, and strong anti-rf interference and anti-near field coupling ability for essential safety requirements. It is also suitable for distribution system and essential safety circuit signal transmission of industrial departments operating in gas explosion environment. Operating conditions: 1) rated voltage is 450/750v. 2) cable conductor long-term allowed working temperature is 70 ℃. 3) the cable temperature under installation should not below 0 ℃, allowed recommended no armoured cable bending radius should not less than 6 times of cable diameter. The armored cable shall not be less than 12 times the outer diameter of the cable.
Correction factor 1.12 1.06 1.00 0.94 0.87 0.79
导线与接线端子之间的接触电阻