二、电缆的型号、名称和用途序号型号名称使用范围1VVVLVVYVLY聚氯乙烯绝缘聚氯乙烯/聚乙烯护套电力电缆敷设在室内、隧道及管道中，电缆不能承受机械外力作用VV22VLV22VV23VLV23聚氯乙烯绝缘聚氯乙烯/聚乙烯护套钢带铠装电力电缆敷设在室内、隧道内直埋土壤，电缆能承受机。
本安计算机电缆 型 号 电缆屏蔽结构及特征 铜芯PVC绝缘 铜芯PE绝缘 铜芯XLPE绝缘 IA-DJVPV IA-DJYPV IA-DJYJPV 本安型、编织分对屏蔽（铜丝或镀锡丝） IA-DJVP2V IA-DJYP2V IA-DJYJP2V 本安型、铜塑复合膜分对屏蔽 IA-DJVP3V IA。
该电缆主要用于交流或直流300V及以下的工作系统，在500V及以下时能正常工作。市内通信电缆、铁路信号电缆、电源线，电气装备用电线电缆，视频线,系统专用电缆。等专业生产厂家。企业拥有职工300多人，工程技术人员30多人，工厂占地面积20000平方米，拥有固定资产1500万元，企业拥有生产和检验设备的总数120多台（件），年产值1.5亿元。
二、型号、名称、适用范围普通型号阻燃型型号名称适用范围KVVP1ZR—KVVP1ZRB—KVVP1ZRA—KVVP1铜芯聚氯乙烯绝缘聚氯乙烯护套铜丝缠绕屏蔽控制电缆用于强电控制系统KVV22-1ZR-KVVP2-1ZRB-KVVP2ZRA-KVVP2铜芯聚氯乙烯绝缘聚氯乙烯护套钢带铠装铜丝屏蔽控制电。
Precautions for installation of power cables: keep 2m distance when the cable is installed in parallel with the thermal pipe, and 0.5m should be maintained when crossing. The cable shall be installed at a distance of 0.5m in parallel or across other pipelines. When the cable is directly buried and installed, the buried depth of 1-35kv cable is not less than 0.7m. When 10KV and below cables are installed in parallel, the net distance between them shall not be less than 0.1m and 10-35kv shall not be less than 0.25m. The distance of cross installation is not less than 0.5m. Cable laying temperature is not lower than 0 ℃, bending radius: multi-core cable or 15 (D + D), a single cable 20 or more (D + D), (D for cable diameter, D) for the conductor diameter. 6 kv and above cable joint: (1) installing a cable terminal head, must be stripped semiconductor electric shielding layer, operation shall not damage the insulation, should avoid mark uneven situation, when necessary use sand paper to grind; The shield end should be flat and the graphite layer (carbon particles) should be cleaned. (2) plastic cable end copper tape screened and armor must be good grounding, the short circuit also follow this principle, avoid unbalanced three-phase run ShiGang armoured end produce inductive electromotive force, and even "lighter" and accidents such as burning sheath. It is required to use my tinplate to braid copper wire for grounding lead. When connecting with the cable copper belt, it should be welded with chromium-iron tin. The shield of three-phase copper tape should be connected with ground wire respectively. Note that the shielded ground wire and steel armor ground wire should be separately drawn out and insulated from each other. The position of the welded ground wire should be as low as possible. Basic requirements for cable terminals and intermediate joints: a. good conductor connection; B. The insulation is reliable, and it is recommended to use irradiated cross-linked heat-shrinkable silicone rubber insulation materials; C. good sealing; D. sufficient mechanical strength to meet various operating conditions. The end of the cable must be used to prevent erosion of water and other corrosive materials, so as to prevent breakdown due to the aging of the insulation layer caused by water trees. Crane or forklift should be used for the loading and unloading of cables. It is forbidden to run flat or lay flat. For installation of large cables, cable laying cart should be used to avoid external damage or abrasion caused by manual dragging. If the cable cannot be laid in time for some reason, it should be stored in a dry place to prevent sunlight from exploding and water entering the end of the cable. Note: the installation of wire and cable should be done by the installation personnel or full-time technical personnel familiar with the performance of wire and cable. If there are still unclear matters, please consult the relevant technical department or the technical department of our factory.
在编制plc程序时，不管是新手还是老手，都会犯下这种低级错误。因为这种错误是非语法上的，所以用编程软件也不能检查出错误之处。此错误一旦发生，自己有时还很难发现，直至上机调试运行时，所控设备不能运行或运行到某个位置停止不前，才察觉出来有问题，再对PLC程序逐条逐句查找分析，或采取对程序逐条逐句执行，费时费工。那么究竟是什么问题易使我们犯下这种低级错误呢？继电器电气控制的固有思维，在编制程序时，某个或几个输入点采用物理常闭触点（如停止开关、行程限位开关），在程序中，仍延续继电器电气控制方式编制，即仍采用常闭接点作为导通条件使用。
天津市电缆总厂第一分厂提供的CPEV-S通信电缆;CPEV-S电缆不仅具有国内外领先的技术水平，更有良好的售后服务和优质的解决方案。HJVV铜芯聚氯乙烯绝缘聚氯乙烯护套局用电缆。HJVVP铜芯聚氯乙烯绝缘聚氯乙烯扩套屏蔽型局用电缆铜芯聚烯烃绝缘铝塑综合护套市内通信电缆。
接地引出线要求采用我镀锡编织铜线，和电缆铜带连接时应用铬铁锡焊，不宜用喷灯封焊，以免烧损绝缘。 ③三相铜带屏蔽应分别与地线相连，注意屏蔽接地线和钢铠接地线应分别引出，相互绝缘，焊接地线的位置应尽量靠下。
Railway cables are suitable for transmission under rated voltage ac 500V or dc 1000V and below. Product name, model, specification and scope: plastic insulation and polyurethane sheath railway cable PTYAH; PTYA; PZYA; PTYV; PTYY,; PTY22; PTY23; (PZY02; PZY03; PZY23 PZY22) 1/0.8mm (1/1.0mm) 2-48 core is suitable for railway communication, fire alarm, telegraph and other automatic devices with rated voltage ac 500V or dc 1000V or below. Poly (PVC insulation composite sheath steel tape armoured polyvinyl chloride sheathed PTYA23 PTYA22 PTY23 PTY22 PTYAH23 PZYA23 PZYA22 PZY23 PZY22 0.8 mm (1/1.0 mm) 4-61 core is fit for ac rated voltage 500 v or dc voltage 1000 v and below transfer audio and fixed laying railway and group control automation assembly line, can transport railway group general automatic letter, also can transmit the audio frequency shift automatic block and business calls. ? 4, using features: cable in - use under 40 ℃ to + 50 ℃. Cable conductor long-term working temperature shall not exceed 70 ℃. Ordinary sheath of the cable laying under the temperature below 5 ℃, resistance to sheath for - 10 ℃. The bending radius shall not be less than 15 times of the outer diameter of the cable (when laying) and shall be applicable to any horizontal difference
RVVP是一种软导体PVC绝缘线外加屏蔽层和PVC护套的电缆.铜芯聚氯乙烯绝缘屏蔽聚氯乙烯护套软电缆电压300V/300V2-24芯用途：仪器、仪表、对讲、监控、控制安装适用范围：适用于交流额定电压300/300V及以下电器、仪表和电子设备及自动化装置等屏蔽线路执行标准■JB8734.5-1998■。
具有良好的信号传输性能。带米标识，分100米、200米、500米、1000米木轮包装。 2、铝箔、裸金属丝编织双层屏蔽，PVC外护套，阻燃,外观紫色。 3、符合VDE 0472标准；B类试验（IEC332.1）。
3. 绝缘厚度：3.3线芯绝缘厚度为0.5，绝缘后外径为3.5毫米。0.85线芯绝缘厚度为0.7绝缘后外径为2.5毫米。4. 成缆时把四根线芯排列为红，绿，蓝，白，排流线，排流线要和线芯一起绞合，千万不要纵放，成缆时不要加填充物，缆芯外用铝箔绕包，而后再绕包一层聚酯膜，在外有一层铜丝编织屏蔽（屏蔽铜丝不镀锡）。
运动目标跟踪运动目标的跟踪，即通过目标的有效表达，在图像序列中寻找与目标模板最相似候选目标区位置的过程。简单说，就是在序列图像中为目标定位。运动目标的有效表达除了对运动目标建模外，目标跟踪中常用到的目标特性表达主要包括：视觉特征(图像边缘、轮廓、形状、纹理、区域)、统计特征(直方图、各种矩特征)、变换系数特征(傅里叶描绘子、自回归模型)、代数特征(图像矩阵的奇异值分解)等。除了使用单一特征外，也可通过融合多个特征来提高跟踪的可靠性，目前主流的方法有：基于区域匹配跟踪算法、基于轮廓匹配跟踪算法、基于特征匹配跟踪算法。
自承式电缆屏蔽：用轧纹或不轧纹金属带纵包子缆芯包带之外，两边搭接。屏蔽带表面涂敷的塑料薄膜与护层粘接自承式电缆护套：黑色低密度聚乙烯。自承式电缆吊线：吊线为7股镀锌钢绞线，标称外径为6．3mm和4．75mm两种，其抗张强度分别不小于3000kg和1800kg，吊线用热塑性涂料涂敷，以防钢丝锈蚀。
产品描述：特性阻抗120欧姆，导体为2*2*24AWG多股镀锡电解铜丝绞合而成，花色绝缘护套宜于安装识别，铝箔/聚酯带总体****屏蔽，附加独立多股绞合镀锡铜丝接地导体，工业灰色PVC外护套，符合ULAWM2919文件。
3、橡皮绝缘电力电缆绝缘层为橡胶加上各种配合剂，经过充分混炼后挤包在导电线芯上，经过加温硫化而成。它柔软，富有弹性，适合于移动频繁、敷设弯曲半径小的场合。常用作绝缘的胶料有天然胶-丁苯胶混合物，乙丙胶、丁基胶等。
矿用通信电缆:1、执行标准：MT818.2用途:本产品用于井下作电话通信焊线、配线和用户线路。3、使用条件电缆使用环境温度为－40℃～+50；在25℃时湿度为95%；电缆敷设温度≥－10℃；电缆敷设时的弯曲半径MHYV≥10倍电缆外径，其余型号≥15倍电缆外径。