供应Delrin? 100 BK602
DuPont Performance Polymers
聚甲醛（POM）均聚物
供应Delrin? 100 NC010
供应Delrin? 100AF
供应Delrin? 100AL NC010
供应Delrin? 100KM NC000
供应Delrin? 100P BK602
供应Delrin? 100P NC010
供应Delrin? 100PE BK602
供应Delrin? 100PE NC010
供应Delrin? 100ST BK602
供应Delrin? 100ST NC010
供应Delrin? 100STE NC010
供应Delrin? 100T BK602
供应Delrin? 100T NC010
供应Delrin? 100TE NC010
供应Delrin? 100TL NC010
供应Delrin? 111DP NC010
供应Delrin? 127UV BK701
供应Delrin? 127UV NC010
供应Delrin? 127UVE NC010
供应Delrin? 127UVE RD402
供应Delrin? 150 NC010
供应Delrin? 300CP BK642
供应Delrin? 300CP NC010
供应Delrin? 300PE BK602
供应Delrin? 300PE NC010
供应Delrin? 300TE BK602
供应Delrin? 300TE NC010
供应Delrin? 311DP BK402
供应Delrin? 311DP NC010
供应Delrin? 327UVE NC010
供应Delrin? 327UVE RD402
供应Delrin? 500AF
供应Delrin? 500AL NC010
供应Delrin? 500CL BK601
供应Delrin? 500CL NC010
供应Delrin? 500P BK602
供应Delrin? 500P NC010
供应Delrin? 500PE BK602
供应Delrin? 500PE NC010
供应Delrin? 500T BK602
供应Delrin? 500T NC010
供应Delrin? 500TE NC010
供应Delrin? 500TL NC010
供应Delrin? 510GR NC000
供应Delrin? 511DP BK402
供应Delrin? 511DP NC010
供应Delrin? 511KM NC000
供应Delrin? 520MP NC010
供应Delrin? 525GR NC000
供应Delrin? 527UV BK701
供应Delrin? 527UV NC010
供应Delrin? 527UVE NC010
供应Delrin? 527UVE RD402
供应Delrin? 570 NC000
供应Delrin? 577 BK000
供应Delrin? 900P BK602
供应Delrin? 900P NC010
供应Delrin? 911DP BK402
供应Delrin? 911DP NC010
供应Delrin? FG100AL NC010
供应Delrin? FG100P NC010
供应Delrin? FG100TL NC010
供应Delrin? FG150 NC010
供应Delrin? FG311DP NC010
供应Delrin? FG400MTD BLA079
聚甲醛（POM）共聚物
供应Delrin? FG400XRD NC010
供应Delrin? FG500AL NC010
供应Delrin? FG500P NC010
供应Delrin? FG500TL NC010
供应Delrin? FG511DP NC010
供应Delrin? FG900P NC010
供应Delrin? SC631 NC010
供应Delrin? SC652 NC010
供应Delrin? SC655 NC010
供应Delrin? SC690 NC010
供应Delrin? SC699 NC010
如果你要找的POM美国杜邦塑料型号没有在上面，请来电咨询我司，我司销售的POM美国杜邦塑料型号齐全，因为型号之多，就没有一一列出
POM塑胶原料的特点：
（1）POM加工前可不用干燥,好在加工过程中进行预热(80℃左右),对产品尺寸的稳定性有好处.
（2） POM的加工温度很窄(0～215℃),在炮筒内停留时间稍长或温度超过220℃时就会分解,产生刺激性强的甲醛气体.
（3） POM料注塑时保压压力要较大(与注射压力相近),以减少压力降.螺杆转速不能过高,残量要少;
（4） POM产品收缩率较大,易产生缩水或变形.POM比热大,模温高(80～100℃),产品脱模时很烫,需防止烫伤手指.
（5） POM宜在“中压、中速、低料温、较高模温”的条件下成型加工,精密制品成型时需用控制模温
(6)具高机械强度和刚性
(7)高的疲劳强度
(8)环境抵抗性、耐有机溶剂性佳
(9)耐反覆冲击性强,良好的电气性质,复原性良好,具自已润滑性、性良好,尺寸安定性